◊◊ Negative Error Codes (0 to -99) General System Errors (VBL Mgr, Queue) 0 noErr 0 for success "OR" 0 smNotTruncated No truncation necessary -1 qErr queue element not found during deletion "OR" -1 smTruncErr Truncation indicator alone is wider than the specified width -2 vTypErr invalid queue element -3 corErr core routine number out of range -4 unimpErr unimplemented core routine -5 SlpTypeErr invalid queue element -8 seNoDB no debugger installed to handle debugger command Color Manager Errors -9 iTabPurgErr from Color2Index/ITabMatch -10 noColMatch from Color2Index/ITabMatch -11 qAllocErr from MakeITable -12 tblAllocErr from MakeITable -13 overRun from MakeITable -14 noRoomErr from MakeITable -15 seOutOfRange from SetEntry -16 seProtErr from SetEntry -17 i2CRangeErr from SetEntry -18 gdBadDev from SetEntry -19 reRangeErr from SetEntry -20 seInvRequest from SetEntry -21 seNoMemErr from SetEntry I/O System Errors -17 controlErr Driver can't respond to Control call -18 statusErr Driver can't respond to Status call -19 readErr Driver can't respond to Read call -20 writErr Driver can't respond to Write call -21 badUnitErr Driver ref num doesn't match unit table -22 unitEmptyErr Driver ref num specifies NIL handle in unit table -23 openErr Requested read/write permission doesn't match driver's open permission, or Attempt to open RAM serial Driver failed -24 closErr Close failed; Permission to close .MPP driver was denied -25 dRemovErr tried to remove an open driver -26 dInstErr DrvrInstall couldn't find driver in resources -27 abortErr IO call aborted by KillIO; Publisher has written a new edition "OR" -27 iIOAbortErr IO abort error (Printing Manager) -28 notOpenErr Couldn't rd/wr/ctl/sts cause driver not opened -29 unitTblFullErr Unit table has no more entries -30 dceExtErr dce extension error File System Errors -33 dirFulErr Directory full -34 dskFulErr Disk full -35 nsvErr No such volume; volume not found -36 ioErr I/O error -37 bdNamErr Bad file name; there may be no bad names in the final system! -38 fnOpnErr File not open -39 eofErr End of file; no additional data in the format -40 posErr Tried to position to before start of file (r/w) -41 mFulErr Memory full (open) or file won't fit (load) -42 tmfoErr too many files open -43 fnfErr File not found; Folder not found; Edition container not found; Target not found -44 wPrErr Disk is write-protected; Volume is locked through hardware -45 fLckdErr File is locked -45 fLckedErr Publisher writing to an edition -46 vLckdErr Volume is locked through software -47 fBsyErr File is busy (delete); Section doing I/O -48 dupFNErr Duplicate filename (rename); File found instead of folder -49 opWrErr File already open with write permission -50 paramErr Error in user parameter list -51 rfNumErr Reference number invalid -52 gfpErr Get file position error -53 volOffLinErr Volume is off line -54 permErr Software lock on file; Not a subscriber [permissions error on file open] -55 volOnLinErr drive volume already on-line at MountVol -56 nsDrvErr no such drive (tried to mount a bad drive num) -57 noMacDskErr not a Macintosh disk (sig bytes are wrong) -58 extFSErr External file system __ file system identifier is nonzero -59 fsRnErr file system internal error: during rename the old entry was deleted but could not be restored. -60 badMDBErr bad master directory block -61 wrPermErr Write permissions error; Not a publisher Font Manager Errors -64 fontDecError error during font declaration -65 fontNotDeclared font not declared -66 fontSubErr font substitution occurred Disk, Serial Ports, Clock Specific Errors -64 lastDskErr -64 noDriveErr drive not installed -65 offLinErr r/w requested for an off-line drive -66 noNybErr couldn't find 5 nybbles in 200 tries -67 noAdrMkErr couldn't find valid addr mark -68 dataVerErr read verify compare failed -69 badCksmErr addr mark checksum didn't check -70 badBtSlpErr bad addr mark bit slip nibbles -71 noDtaMkErr couldn't find a data mark header -72 badDCksum bad data mark checksum -73 badDBtSlp bad data mark bit slip nibbles -74 wrUnderrun write underrun occurred -75 cantStepErr step handshake failed -76 tk0BadErr track 0 detect doesn't change -77 initIWMErr unable to initialize IWM -78 twoSideErr tried to read 2nd side on a 1-sided drive -79 spdAdjErr unable to correctly adjust disk speed -80 seekErr track number wrong on address mark -81 sectNFErr sector number never found on a track -82 fmt1Err can't find sector 0 after track format -83 fmt2Err can't get enough sync -84 verErr track failed to verify -84 firstDskErr -85 clkRdErr unable to read same clock value twice -86 clkWrErr time written did not verify -87 prWrErr parameter RAM written didn't read-verify -88 prInitErr InitUtil found the parameter RAM uninitialized -89 rcvrErr SCC receiver error (framing, parity, OR) -90 breakRecd Break received (SCC) AppleTalk Errors -91 ddpSktErr Error opening socket "OR" -91 eMultiErr Invalid address or table is full -92 ddpLenErr Data length too big "OR" -92 eLenErr Packet too large or first entry of the write-data structure didn't contain the full 14-byte header -93 noBridgeErr No router available [for non-local send] -94 lapProtErr error in attaching/detaching protocol "OR" -94 LAPProtErr Protocol handler is already attached, node's protocol table is full, protocol not attached, or protocol handler pointer was not 0 -95 excessCollsns Hardware error [excessive collisions on write] -97 portInUse driver Open error code (port is in use) -98 portNotCf driver Open error code (parameter RAM not configured for this connection) -99 memROZErr hard error in ROZ -99 memROZError hard error in ROZ -99 memROZWarn soft error in ROZ